Victron energy BlueSolar SCC010005000 Manual Download Page 65

Page: 65 / 122

Press MENU

to enter

the next display

Short-circuit protection setting

Some inductive or capacitive loads will trigger

the short-circuit protection during start up.

Therefore the SC-protection can be disabled

manually. Sc.F = OFF, Sc.n = ON. The

default is ON.

Discharge current display:

load current and battery capacity,

Press MENU

to enter next display.

USB Voltage display:

USB voltage

5V (2A max)

Press MENU

to enter next display.

Internal controller temperature.

If the controller overheats it will shut

down and wait for the temperature to drop to normal level and then it will

start working again.
Press MENU

to enter Main display.

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands