Victron energy BlueSolar SCC010005000 Manual Download Page 61

Page: 61 / 122

1. Connect the battery - plus and minus.

2. Connect the solar array - plus and minus.

3. Connect the load - plus and minus.

The reverse order applies when deinstalling.

An improper sequence order can damage the BlueSolar PWM Charge Controller!

1. Make sure the battery is charged for the BlueSolar PWM Charge Controller to recognize

the battery type before first installation.

2. The battery cable should be as short as possible to minimize losses.

3. The controller is suitable only for lead-acid, and LiFePO4 batteries.

4. The BlueSolar PWM Charge Controller is suitable only for regulating solar panels. Never

connect another charging source to the charge BlueSolar PWM Charge Controller.

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands