Victron energy BlueSolar SCC010005000 Manual Download Page 104

Page: 104 / 122

REMOTE METER DISPLAY:

LEDs on the top of the LCD
1.

Charging LED: green on, charging

Error LED: red on, error

REMOTE METER OPERATION INSTRUCTION:

the key(from left to right) is: K1-K4, or Next , Left , Right

, Set

The meter display in following order:

Solar panel, battery 1, battery 2, other data as four team data. Use K2 or K3 to check the data between the teams. Symbol Is the
repeat between the team 1 and team 4. K1 is the key for repeating the data of the team. Data shows as following picture.

Error indicator

Setting icon

Circle indicator

Backlight icon

Self-test indicator

Remote
temp. icon

Local temp.
sensor icon

Unit indicator

Battery
icon

Solar icon

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands