Victron energy BlueSolar SCC010005000 Manual Download Page 41

Page: 41 / 122

If the battery is connected with inverse polarity, the output polarity

will also inverse.

A 20A fuse should be inserted in the positive wire to the battery.

Connect the photovoltaic module to the charge regulator. If there is
sunshine, the charging indicator should turn on.

Connect the load to the charge controller; press the ON/OFF button to

start.

3. LED INDICATORS

Green LED is ON when solar is charging the battery.

In case of system over voltage the green LED blinks.

Green LED is ON when the battery voltage is in the right range.

Green LED is slowly flashing when the battery is fully charged.

Yellow LED is ON when the battery voltage is low.

Red LED is ON when the load is cut off.

In case of overload the red LED is slowly flashing

(The load current is 1.25 times of rated current for 60 seconds, or

the load current is 1.5 times of rated current for 5 seconds)

Red LED is fast flashing in case of short-circuits.

Red LED is ON when the push button is ON.
Red LED is OFF when the push button is OFF.

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands