Victron energy BlueSolar SCC010005000 Manual Download Page 40

Page: 40 / 122

2. INSTALLATION

Connect the individual components as shown.

Solar panel(s)

Battery and loads in order indicated 1-6.

Install the regulator near the battery. The installation environment should be
indoor, dry and nonflammable. The cables should be as short as possible and

have a suitable cable diameter size to minimize loss, e.g. use 2.5 mm² at 10A;

use 5 mm² at 20A

Mount the controller on a vertical surface. Allow space above and below

the controller for air flow.

Connect the battery to the controller. If the connection is correct, the

battery indicator will be on.

Important note: Always connect the batteries first.

Summary of Contents for BlueSolar SCC010005000



























































































































Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands

Victron energy BlueSolar SCC010005000, Manual

Search results

Summary of Contents for BlueSolar SCC010005000

Reviews:

Related manuals for BlueSolar SCC010005000

Brands by name

Popular brands