Appendix D - ATC-5000NG Compatibility Command Set
Rev. L0
ATC-5000NG ATC/DME Test Set Operation Manual
Appendix -
D
February 2020
Subject to Export Control. See Cover Page for details.
Page 21
INTERROGATION:P4
Partial
Allows input of width up to 3.55, but maximum transmitted
P4 pulse width is 2.75.
:ATC:XPDR:PUL:P145
:ATC:XPDR:DBL:1:PUL:P145
:ATC:XPDR:ITABLE:1:PUL:P145
Sets P4 pulse level, width and position
(deviation).
INTERROGATION:P4?
Yes
:ATC:XPDR:PUL:P145?
:ATC:XPDR:DBL:1:PUL:P145?
:ATC:XPDR:ITABLE:1:PUL:P145?
Returns P4 pulse level, width and position
settings.
INTERROGATION:P6
Partial
The pulse width range is limited to -0.5 and +1.45.
:ATC:XPDR:PUL:P165
:ATC:XPDR:DBL:1:PUL:P165
:ATC:XPDR:ITABLE:1:PUL:P165
Sets P6 pulse status (level), width and position
(deviation).
INTERROGATION:P6?
Yes
:ATC:XPDR:PUL:P165?
:ATC:XPDR:DBL:1:PUL:P165?
:ATC:XPDR:ITABLE:1:PUL:P165?
Returns P6 pulse level, width and position
setting.
INTERROGATION:P6:SPR
Partial
ATC5000NG will not disable SPR.
:ATC:XPDR:PUL:P1SPS
:ATC:XPDR:DBL:1:PUL:P1SPS
:ATC:XPDR:ITABLE:1:PUL:P1SPS
Sets SPR control and position.
INTERROGATION:P6:SPR?
Yes
:ATC:XPDR:PUL:P1SPS?
:ATC:XPDR:DBL:1:PUL:P1SPS?
:ATC:XPDR:ITABLE:1:PUL:P1SPS?
Returns SPR control and position setting.
REPLY:ATCRBS?
Partial
X pulse and Ident are not reported.
:ATC:XPDR:AREP? or
:ATC:XPDR:CREP?
Returns Mode C reply altitude or Mode A reply
identification.
REPLY:DELAY:FIRST?
Yes
:ATC:XPDR:DREP?
Returns reply delay for current function.
REPLY:JITTER?
Yes
:ATC:XPDR:JREP?
Returns Mode S format and data received in
replies to ATC, ACS or ACL interrogations.
REPLY:MODES?
Yes
:ATC:RCV:LOG:DL?
Returns Mode S format and data received in
replies to ATC, ACS or ACL interrogations.
REPLY:SPACING?
Partial
Must select F2 to get the spacing measurement.
:ATC:MEA:PUL:POS?
Returns reply pulse spacing in μs.
REPLY:TIMEOUT
Yes
Sets time limit for getting no reply in seconds.
REPLY:WIDTH?
Partial
REPLY:WIDTH? "ATC" functions properly.
REPLY:WIDTH? "MODES" returns all zeros even with width
displayed on unit.
:ATC:MEA:PUL:WID?
Returns width of reply pulses in μs.
C30 COMMANDS
REPLY:PERCENT?
Yes
:ATC:XPDR:PREP?
Sets percent reply through selected antenna for
set type.
REPLY:PERCENT:CLEAR
Yes
Clears percent reply readings.
C40 COMMANDS
S-1403DL COMMAND
SUPPORTED
COMMENTS
ATC5000NG EQUIVALENT (OR
SIMILAR)
COMMAND DESCRIPTION
Summary of Contents for 138156
Page 3: ......