Vari Agatha, Translation Of The Original Instructions, Page: 38 / 68

Agatha
2. Press the right button marked START and hold it for a maximum of 5 seconds before the electric starter starts the engine 87 ,
then release the button.

Do not try to start an already started engine! You can destroy the starter.

Do not go away from the machine!
3.4.2.1.2 M
ECHANICAL CHOKE ENGINE
1. Shift the accelerator lever in
Pict.8
. into 3 CHOKE position.

Start an already warm engine with the accelerator lever in position 3 MAX.
2. Start the engine by pulling the manual starter cord 88 .
3. Let the new or cold engine run for about 30 seconds on the choke (accelerator lever in position 4 CHOKE ), then move the
accelerator lever to position 3 MAX .

Do not go away from the machine!
3.4.2.1.3 A
UTOMATIC CHOKE ENGINE
1. Shift the accelerator lever in
Pict.8
. into 3 MAX position.
2. Start the engine by pulling the manual starter cord 89 .
3. The automatic choke adjusts the speed setting itself when the engine warms up
90
.

Do not go away from the machine!
3.4.2.2 S
TARTING UP THE CUTTING DISC

Make sure that all persons, animals and children are at a safe distance from the machine! If they are not, do not
continue in your activity!
1. Start the engine
91
. If the engine is cold, allow it to warm up at maximum speed for about 1 minute.
2. Take hold of the handlebars handle with your left hand. With your right hand then slowly push the lever ( 16 in Pict.2 ) on the
right handle.

Slowly press the lever up to about two thirds throttle, to start up the cutting disc and prevent the engine form
turning off.
3. After starting up the cutting disc, press the lever to the handle and hold firmly.

The cutting disc start-up is accompanied by V-belt creeping and its side effects (chattering, whistling). These
effects usually disappear when the V-belt is run-in.
Note:
During the first starts of the cutting disc, a new or cold engine might stall. This tendency disappears after warming up the engine. In
case the cutting disc drive cannot be runned up, check if there is a defect according to Table 10 .
3.4.2.3 P
UTTING THE MACHINE IN MOTION
To put the machine in motion use lever 17 in Pict.4 on the left handle. Press the lever all the way to the handle, and the machine
moves ahead immediately. Adjust the speed of your walk to machine speed as soon as you press the lever and the machine moves.
The wheel drive has a belt clutch; you can press the lever slowly and the machine starts off fluently, not with a jump.

Always press the clutch lever all the way down to the handlebars. If the lever is not pressed properly, it causes
damage to the V-belt.

The wheel drive clutch lever does not adjust travelling speed!

Never reverse with the wheel drive clutch pressed!
3.4.2.4 M
ACHINE STOPPING
If you wish to stop the machine, release the left handlebar lever. The machine stops moving, but the cutting disk spins. The cutting disc
drive is turned off by releasing the right handlebar lever. The cutting disc is stopped by an automatic brake. Shift the accelerator lever into
MIN or STOP position. To switch off the engine on machines equipped with a start panel Pict.9 , press the left button STOP .

Always switch off the engine and wait for the cutting disk to stop before starting any activity near the machine!
Always switch the engine off before leaving the machine!

Never leave the engine running at the maximum engine speed for a long time or running idle while the clutch
of the cutting blade drive and wheel drive are turned off! The machine drive parts could be damaged (V-belt,
belt pulley, clutch pulley, etc.)!
87 Wait at least 10 seconds between start cycles.
88 Instructions for starting the engine are described in detail in the engine operating instructions.
89
Instructions for starting the engine are described in detail in the engine operating instructions.
90
Depending on the ambient temperature and the engine temperature, the automatic choke is activated for approx. 1 minute.
91
Differences in starting the engine are described in chapter 3.4.2.1.
38
R
ev
iz
e
0
7
/2
0
2
1