UTICA BOILERS MACF-115 Manual Download

Page: 22 / 139

5.3 Definitions

Coaxial piping

– Exhaust and air intake pipe have a

common axis.

5 - COMBUSTION AIR AND VENT PIPING

Twin Pipe –

Exhaust and intake air are separate

pipes, can be terminated using single wall

terminals from the vent manufacturer or field built

configuration using elbows or tees.

5.2 Removal of Existing Boiler From Common Vent

System

When existing boiler is removed from common venting

system, common venting system is likely to be too large

for proper venting of appliances remaining connected to

it.
After removal of existing boiler, following steps shall be

followed with each appliance remaining connected to

common venting system placed in operation, while other

appliances remaining connected to common venting

system are not in operation:

• Seal any unused openings in common venting

system.

• Visually inspect venting system for proper size and

horizontal pitch. Determine there is no blockage or

restrictions, leakage, corrosion and other deficiencies

which could cause an unsafe condition.

• When practical, close all building doors, windows,

and all doors between space in which appliances

remaining connected to common venting system are

located and other spaces of building. Turn on clothes

dryer and any appliance not connected to common

venting system. Turn on exhaust fans, such as range

hoods and bathroom exhaust so they will operate at

maximum speed. Do not operate summer exhaust

fan. Close fireplace dampers.

• Turn on appliance being inspected. Follow lighting

instructions. Adjust thermostat so appliances will

operate continuously.

• Test for spillage at draft hood relief opening after

5 minutes of main burner operation. Use flame of

match or candle, smoke from cigarette, cigar or pipe.

• Determine each appliance remaining connected to

common venting system properly vents when tested

as outlined above. Then return doors, windows,

exhaust fans and any other gas-burning appliance to

their previous condition of use.

• Any improper operation of common venting system

should be corrected so installation conforms with

National Fuel Code, ANSI Z223.1/NFPA 54 and/or

Natural Gas and Propane Installation Code, CAN/

CSA B149.1. When re-sizing any portion of common

venting system, common venting system should be

re-sized to approach minimum size as determined

using appropriate tables in Chapter 13 of the National

Fuel Gas Code, ANSI Z223.1/NFPA 54 and/or Natural

Gas and Propane Installation Code, CAN/CSA B149.1.

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands