UTICA BOILERS MACF-115 Manual Download Page 87

Page: 87 / 139

IMPORTANT SAFETY INFORMATION

CAUTION

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

WARNING

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

DANGER

Indicates a hazardous situation which, if not

avoided, WILL result in death or serious injury.

This is the safety alert symbol. Symbol alerts you to

potential personal injury hazards. Obey all safety messages

following this symbol to avoid possible injury or death.

Become familiar with symbols identifying

potential hazards.

General

Boiler installation shall be completed by qualified agency.

See Installation, Operation & Maintenance Manual for

additional information.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death

or serious injury. Read this manual and understand

all requirements before beginning installation.

Installation shall conform to requirements of

authority having jurisdiction or in absence of such

requirements:

•

United States

• National Fuel Gas Code, ANSI Z223.1/NFPA 54

• National Electrical Code, NFPA 70.

• Canada

• Natural Gas and Propane Installation Code, CAN/

CSA B149.1.

• Canadian Electrical Code, Part I, Safety Standard for

Electrical Installations, CSA C22.1

Where required by authority having jurisdiction,

installation shall conform to Standard for Controls

and Safety Devices for Automatically Fired Boilers,

ANSI/ASME CSD-1.

Additional manual reset low water cutoff and/or high limit

may be required.

Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not

limited to:

• Installation by licensed plumber or gas fitter.

WARNING

Fire, Explosion, Asphyxiation, Electrical shock

hazard! Flooding will result in damages such as

electrical problems, corrosion, inoperative parts,

mold and other unforeseen issues which can

occur over time. Any equipment determined by

a professional as damaged by a flood, defined

as excess of water or other liquid, shall be

replaced. Failure to follow these directions will

result in a Hazardous Situation.

PN 240012875 REV. C [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Brands by name

Popular brands