UTICA BOILERS MACF-115 Page 91 Manual Download

Page: 91 / 139

Note

Provided Wiring and Piping illustrations

are meant to show system concepts only.

Installer is responsible for all equipment

required by authority having jurisdiction.

Note

Arrange piping to prevent water dripping

onto boiler.

All piping diagrams are shown with optional DHW Indirect

Tank where applicable.

GENERAL INFORMATION - HYDRONIC PIPING

Water

Temperature

Setting

1st Degree Burn

Exposure Time For

An Adult

2nd and 3rd Degree Burn

Exposure Time For An

Adult

120° F

1 minute

5 minutes

130° F

5 seconds

30 seconds

140° F

2 seconds

5 seconds

150° F

1 second

1.5 seconds

160° F

Instantaneous

0.5 seconds

Note:

Warning for Infants, Children, and Elderly:

Great care must be taken when exposing the

aforementioned groups to warm or hot water as they

can be badly burned in exposure times less than half

of the time for an adult.

Use of Buffer Tank:

☐

If using internal boiler pump, manifold shall be cut for

use as shown on page 24. Increase pipe size to match

Buffer tank connections as shown.

☐

Locate tank as close to boiler as possible.

The Labor Saver Piping Manifold, which is supplied with

each boiler, is shown with most of the following piping

diagrams.

Use of Indirect Water Heater (DHW) Heating

Only Boiler:

Note

Sensors supplied with this boiler are

proprietary to the manufacturer. Use of

alternate sensors

WILL

diminish boiler

performance.

☐

Use DHW sensor kit 550003189 to interface with

boiler. Wire to M2 terminals #3 and #4. Exception: not

applicable for the 165 model, use aquastat for indirect

tank control.

☐

For heating only boilers with DHW outlet connection,

see page 4, indirect water heater shall be piped

utilizing the internal boiler pump. See pages 10 and 13.

☐

Locate tank as close to boiler as possible.

☐

See Indirect Tank Performance chart, page 40 of this

manual.

☐

Change P03 on boiler for application as specified on the

applicable wire diagram in this manual or Boiler Control

Section 9 of Installation, Operation & Maintenance

Manual supplied with the boiler.

PN 240012875 REV. C [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands