UTICA BOILERS MACF-115 Page 72 Manual Download

Page: 72 / 139

• APPLIANCE -

Device to convert gas into energy;

term includes any component, control, wiring, piping

or tubing required to be part of the device.

• ANSI

- American National Standards Institute, Inc.

over see's creation and maintenance of voluntary

consensus standards, including ANSI Z21.13/CSA 4.9:

Gas-Fired Low Pressure Steam and Hot Water Boilers.

• ASME -

Association of Mechanical Engineers

Establishes rules of safety governing the design,

fabrication, and inspection of boilers and pressure

vessels, determining the MAWP of such vessels.

• ASTM

- American Society for Testing and Materials.

ASTM International is one of largest voluntary

standards development organizations in world trusted

source for technical standards for materials, products,

systems, and services. Known for their high technical

quality and market relevancy, ASTM International

standards have important role in information

infrastructure that guides design, manufacturing and

trade in the global economy.

• AUTHORITY HAVING JURISDICTION

Individual

or organization adopting and enforcing codes,

rules, and by-laws governing various concerns of

community. Commonly referred to as "final authority"

for any matters relating to LIFE SAFETY and BUILDING

CONSTRUCTION within a community.

• BOILER

- Appliance intended to supply hot liquid for

space-heating, processing or power purposes.

• BTU

- Abbreviation for British Thermal Unit. Quantity

of heat required to raise temperature of 1 pound of

water 1°F.

• BURNER

- Device for final conveyance of gas or

mixture of gas and air, to combustion zone.

• CALIBRATE

- Make fine adjustments or divide into

marked intervals for optimal measuring.

• COAXIAL VENTIN

G Sharing the same center.

• COMBUSTION

- Rapid oxidation of fuel gases

accompanied by production of heat or heat and light.

Complete combustion of fuel is possible only in

presence of adequate supply of Oxygen.

• COMBUSTIBLE MATERIAL

- Materials made of or

surfaced with wood, compressed paper, plant fibers,

or other materials capable of being ignited and

burned. Such material shall be considered combustible

even though flame-proofed, fire-retardant treated, or

plastered.

• COMBUSTION AIR

- Air that is drawn into an

appliance to mix with fuel and support combustion.

• CONDENSATE

- Liquid separated from flue gas due to

reduction in temperature.

• DIRECT VENT BOILER

- Boiler constructed and

installed so all combustion air is derived directly

from outdoors and all vent gases are discharged to

outdoors.

• DOMESTIC -

Relating to household usage as opposed

to commercial usage.

• DOMESTIC WATER -

Potable drinking water - tap

water.

• DRAFT

- Pressure difference causes gases or air to

flow through a chimney, vent, flue or appliance.

• FLA

- Full load amps.

• FLUE

- Enclosed passageway for conveying

combustion gases.

• FLUE GASES

- Products of combustion plus excess

air in appliance flues or heat exchanger.

• GAS SUPPLIER -

Party that sells commodity of

Natural Gas (Gas A) or LPG (Gas E).

• HIGH-VOLTAGE

- Circuit involving potential of not

more than 600 volts and having circuit characteristics

in excess of those of low-voltage circuit.

• HYSTERESIS (DIFFERENTIAL) -

difference

between the temperature at which the thermostat

switches off - and the temperature at which it

switches on again.

• IGNITER

- Device utilizing electrical energy to ignite

gas at main burner.

• LEAK CHECK

- Operation performed on gas piping

system to verify system does not leak.

• LICENSED QUALIFIED INSTALLER / SERVICE

TECHNICIAN -

any individual, firm, corporation

or company that either directly or through a

representative is engaged in the installation,

replacement, repair or servicing of gas piping, venting

systems, appliances, components, accessories, or

equipment, and whose representative is experienced

and trained, in such work and has complied with the

requirements of the authority having jurisdiction.

• LOW WATER CUTOFF

- Device constructed to

automatically cut off fuel supply when surface of water

in boiler falls to lowest safe water level.

• LOW-VOLTAGE

- Circuit involving potential of not

more than 30 volts.

14 - GLOSSARY

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands