manualshive.com logo in svg

UTICA BOILERS MACF-115, Manual

Share
Download
UTICA BOILERS MACF-115 Manual Download Page 139

Inspection Items

Date Completed

Year 

1

Year 

2

Year 

3

Year 

*4

Piping

Near boiler piping

Check boiler and system piping for any sign of 

leakage, verify pipes are properly supported.

Vent

Check condition of all vent pipes and joints.  Verify 

vent piping terminations are free of obstructions 

and blockages.

Safety Relief Valve

Follow safety relief valve manufacturer's 

instructions for maintenance and repair. Verify 

dischage pipe properly installed per IOM.

System

Visual

Do full visual inspection of ALL system 

components.

Functional

Test all functions of the system (heat and safety)

Temperatures

Verify safe settings on boiler or anti-scald valve.
Verify programmed temperature settings.

Electrical

Connections

Check wire connection. Verify connections are 

tight.

Smoke and Co detector

Verify devices are installed and working properly.  

Change batteries if necessary.

Circuit Breakers

Check that circuit breaker is clearly labeled and 

operates correctly.

Chamber/

Burner

Combustion Chamber

Check burner and combustion chamber.  Clean 

following directions in maintenance section of IOM.  

Replace gaskets whenever checking combustion 

chamber.

Spark Electrode

Clean. Set gap according to IOM directions.  Clean 

electrode with plumbers cloth to remove oxides.

Flame Sensor

Clean sensor. 

Condensate

Neutralizer

Check condensate neutralizer - replace if 

necessary.

Condensate pipe/trap

Disconnect condensate pipe. Clean out any dirt 

or accumulation. Fill with water level of outlet 

and reinstall.  NOTE: verify flow of condensate, 

make sure hose is properly connected during final 

inspection.

Gas

Pressure

Measure incoming gas pressure per IOM.

Pressure drop

Measure drop in pressure on light off verify with 

IOM. 

Leaks

Check gas piping. Test for leaks and signs of aging.  

Make sure all pipes are properly supported.

Combustion CO/CO

₂

 Levels

Check CO and CO

₂

 level in exhaust. See Start-up 

Procedures for ranges. Record at high and low fire.

Safety

All Sensors

Check continuity of all sensors. Replace if corroded. 

Verify all connections through ohms reading.

Final 

Inspection

Check List

Verify you have completed entire check list.

Homeowner

Review findings and service with Homeowner.

Required

 Inspection Schedule

To Be Completed By

Qualified Service Technician 

* Continue inspections beyond 4th year.  Maintenance should continue annually for the life of the boiler to ensure 

safe worry free operation.

PN 240011561 REV B, [09/19/2018]

Summary of Contents for MACF-115












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands