UTICA BOILERS MACF-115 Page 70 Manual Download

Page: 70 / 139

To RESET boiler press

button for at least 2 seconds.

For other error codes not described in table please contact manufacturer at 1(800) 325-5479.

13 - TROUBLE SHOOTING

13.1 Error Messages and Resetting the Boiler - continued

Anomalies Only Displayed in the Fault History

E62

Anti-wind activation with increase of the minimum

fan speed

Check the position of the terminal of the flue duct.

E63/E65

Combustion level out of range

Check flue recirculation and combustion levels.

E65

Maximum value of the speed reached / correction of

the flame signal

Check flue recirculation on the flue duct.

E67

Anti-wind activation at maximum power

Check the position of the terminal of the flue duct.

E69

Combustion level out of range

Check flue recirculation and the combustion levels.

E70

Flame signal problem/micro interruption of the

flame signal

Check cable and integrity of the sensing electrode, verify the

continuity between burner and earth.

E73

Combustion adjustment / modified during operation

Review and monitor other codes such as

E53

and

E92

Error Description

Operation

135

Internal error

Verify all cables. Replace PCB.

160

Fan fault

Check fan and cable

162/317

Incorrect power supply frequency.

169

Flue pressure switch (contact open)

Check pressure switch and cable.

Check obstruction on flue pipe

164/384

Fault flame (parasitic flame).

Check correct operation of T. gas valve.

165/385

Input voltage too low.

Check power supply

E178

Low return water temperature / anti-freeze

function active

Check the return water sensor, check the circulator, check the

correct circulation of the water. Boiler will exit status when

condition is resolved.

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands