UTICA BOILERS MACF-115 Page 52 Manual Download

Page: 52 / 139

9.5 Control Panel

To enter the

INFO

Menu press and hold

for 1 second.

Press and hold the

button for 1-2 seconds to increment

through the selections as shown in the table below.
Press

to exit.

DHW temperature adjustment

(+ to increase the temperature and – to decrease it)

Heating water temperature adjustment

(+ to increase the temperature and – to decrease it)

Boiler operating information

Operating mode:

DHW – DHW & Heating – Heating Only

ON/Off – Reset – Exit menu/functions

BUTTONS Key

Off: heating and DHW disabled (only boiler frost protection is active)

Burner lit

Ignition fault

DHW operating mode enabled

Boiler/system water pressure low

Heating mode enabled

Call a qualified service technician

Programming menu

Manually resettable fault ( )

Boiler information menu

Fault in progress

Set unit of measurement (SI/US)

SYMBOL Key

DESCRIPTION

Secondary fault internal code

Setpoint Central Heating (°F/°C)

Heating flow temperature (°F/°C)

10/11

Manufacturing information

Outdoor temperature (°F/°C)

Flue sensor temperature (°F/°C)

Indirect Tank DHW temperature (boiler CH only)

Manufacturing information

Domestic hot water temperature (boiler with plate exchanger)

Identification Open Therm communication

Water pressure in heating system (PSI/bar)

Manufacturing information

Heating return temperature (°F/°C)

Manufacturing information

Thermo fuse status (000/001)

Fan speed (“i17”x100)

Not used

Manufacturing information

9 - START UP PROCEDURE

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands