UTICA BOILERS MACF-115 Manual Download

Page: 114 / 139

ACCESSORIES

Flow Temp

Outside Temp

1k Ω

Note

°F

°C

80 Is Default.

For temperatures below -40°F (-40°C), maximum heating flow temperature set point no longer

increases and curves on the graph become horizontal. Boiler set point will override sensor

setpoint.

Boiler Control Panel

(CH)

Heating Water

Adjustments

Operating

Mode

Display

1. 1K Ohm (1K

Ω)

Outdoor Temperature

Sensor Kit - BD710487302V

•

Use the Outdoor Sensor (OAS) Kit with Heating Only

or Combi Boilers.

• Wire Control to boiler M2 terminal strip, terminals 4 and

5 as shown.

• Install/locate Control follow supplied instructions with

sensor kit and Installation, Operation and Maintenance

Manual (IOM).

Setting “Kt” Climate Curve:

Boiler automatically recognizes OAS sensor when wired to

M2 terminal block. Display changes to show current default

“

” value (80). Note display value.

When operating in CH mode, boiler setpoint is determined

by the

value selected and actual outside air

temperature. Refer to applicable °F (or °C) chart, (pg. 30)

for setpoint information.

• Select

range which will satisfy the desired boiler

delivery temperature based on outdoor temperature

range expected for your location. For example: if you

need 176°F water when the outside temperature is 20°F

and colder, select 35 for your

setting.

•

To change”default”

value on boiler control use

CH Heating buttons.

• Restrict the upper limit of the

curve by using Parameter

P16 to set the maximum boiler water temperature. P16

Default is 176°F.

When OAS is installed, pressing

buttons will

no longer display boiler CH setpoint temperature. It now

displays the

value which can range from 10 to 90.

When scrolling has stopped, boiler will automatically

“SAVE” value as new

default value and automatically

return to CH mode when no

adjustment activity

is sensed.

values can be changed in +/- 1 point

increments.

To return, to verify or change current

“default value,

depress one of the CH setpoint adjustment buttons (once),

, while in any heating or standby mode. Adjust

value to obtain desired comfort level.

PN 240012875 REV. C [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands