UTICA BOILERS MACF-115 Manual Download

Page: 44 / 139

WARNING

Electrical shock hazard. Turn OFF electrical

power supply at service panel before making

electrical connections. Failure to do so could

result in death or serious injury.

Note

Wiring diagrams can be found in Appendix
A of this Manual.

8.3 Electrical Connections

• Boiler requires 120V 60Hz power supply. Verify

electrical supply is polarized.

• Boiler shall be grounded and on dedicated circuit.

• Shall be one common isolator, providing electrical

isolation for boiler and any external controls. Using

PVC insulated cable 18 AWGx3C 221°F (105°C).

• All wiring must be installed in accordance with

requirements of the National Electrical Code and any

additional national, state, or local code requirements

having jurisdiction. All wiring must be N.E.C. Class 1.

• Canada, installation must conform to CSA C22.1

Canadian Electrical Code Part 1 and any local codes.

• If replacing original boiler wiring use only TEW 105°C

or equivalent.

•

If appliance is connected to in floor system, install

limit thermostat to prevent latter from overheating.

DANGER

Electrocution Hazard! HIGH VOLTAGE -

Connections in terminal block M1 are high

voltage (120V / 60Hz). Before making

connections, verify appliance is disconnected

from power supply. Respect the input polarity

on terminal block M1: L (LINE) - N (NEUTRAL).

Failure to follow these instructions WILL result in

death or serious injury.

8 - ELECTRICAL CONNECTIONS

FIGURE 8-1 Junction Box Left side of Boiler

Junction Box

with Knockouts

and grommets

8.2 Install Room Thermostat

Install room thermostat on inside wall. Do not install

where it will be influenced by drafts, hot or cold water

pipes, lighting fixtures, television, sun rays or near a

fireplace.

8.1 General

Electrically bond boiler to ground in accordance with

requirements of authority having jurisdiction. Refer to:

• USA- National Electrical Code, ANSI/NFPA 70.

• Install all wiring in accordance with requirements of

National Electrical Code and any additional national,

state, or local code requirements having jurisdiction.

• All wiring shall be N.E.C. Class 1.

• Boiler shall be electrically grounded in accordance

with the National Electrical Code, ANSI/NFPA No.

70-latest edition.

• Boiler requires a 120V 60Hz power supply. Ensure

electrical supply is polarized.

• There shall only be one common isolator, providing

complete electrical isolation, for boiler and any

external controls. Using PVC insulated cable 12

AWGx3C 221°F (105 ºC).

Model

Size

100

115

125

150

165

205

Power Supply

120V - 60Hz

Power

Consumption 118 W 125 W 133 W 142 W

173 W

182 W

Internal Fuse

(Qty. 2)

F3.15 A

Electrode

Spark Gap

1/8" to 3/16" [3.1 mm to 4.7 mm]

240013371 REV B, [10/01/2021]

Summary of Contents for MACF-115












































































































































Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands

UTICA BOILERS MACF-115, Manual

Search results

Summary of Contents for MACF-115

Reviews:

Related manuals for MACF-115

Brands by name

Popular brands