UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 47

Page: 47 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

Parts List

Letter Description

Quantity Part Number

Ultra Mountain Climber

02-07-0034
33-12-0014
33-11-0008
33-11-0200
33-11-0400

Hardware Complete

M10 x 70 BHCS Bolt

M10 Lock Nut

M10 Flat Washer

1. Place Climber Supports in position.

2. Place Ultra Mountain Climber(A) onto
Climber supports. Align supports
as necessary.

3. From underside of Ultra Mountain Climber(A),
insert pencil through holes in Climber
Supports and mark all hole positions.

4. Drill (9) 3/8” holes into Ultra Mountain Climber(A) using
pencil marks as guide.

See Figure 1.

Place Ultra Mountain Climber(A) back onto Climber Supports.

6. From top side of Ultra Mountain Climber(A), Insert Bolt(B) and
Flat Washer(C) into hole in Ultra Mountain Climber(A), through
holes in Deck Mounting Bar and secure with Flat
Washer(C) and Lock Nut(D).

See Figure 2.

Lightly tighten bolts until all
hardware is installed.

7. Repeat Step 6 for Long Climber
Support and Short Climber Support.

8. Tighten all bolts.

Figure 1

Figure 2

If installation
requires concrete footers,
attach In-ground Footers to
Footer Plate at this time.

Deck Mounting Bar

Long
Climber
Support

Short
Climber
Support

Bolts(B) MUST be cut off

if more than (2) threads

extend beyond Nut(D)

when tightened .

STEP 19 - ATTACH ULTRA MOUNTAIN CLIMBER TO SUPPORTS

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands