UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 55

Page: 55 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

STEP 24 - ATTACH CURVED SLIDE TO DECK

Parts List

Letter Description

Quantity Part Number

02-07-0062
02-07-0043
33-12-0038
33-11-0005
33-11-0400
33-11-0002
33-11-0201
33-11-0200

Center Support Post
Footer

1
1

Hardware Complete

M10 x 35 BHCS Bolt

M10 Lock Nut

M10 x 20 BHCS Bolt

M10 Lock Washer

M10 Flat Washer

Figure 1

Figure 2

1. Choose appropriate hole in Footer(B) for
your surfacing application.

2. Insert Footer(B) inside of Center Support
Post(A) and align holes.

3. Insert Bolt(C) through larger hole in Center
Support Post(A), into Footer(B) and through
other side of Center Support Post(A) and
secure with Lock Nut(D).

See Figure 1.

4. Place mounting plate of Center Support
Post(A) against the underside of Curved Slide and align holes.

If installation requires concrete footers, install In-Ground footers at this time.

5. Insert (2)Bolts(E), (2)Lock Washers(F) and (2)Flat Washers G) into
mounting plate and into threaded inserts in slide.

See Figure 2.

Insert both Bolts(E) before tightening.

6. Tighten all Bolts

Mounting

Plate

Curved

Slide

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands