UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 28

Page: 28 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

UPRIGHT FOOTER

(Part# 02-07-0042)

HANDRAIL FOOTER

(Part# 02-07-0043)

IN-GROUND FOOTER

(Part# 02-07-0049)

FOOTER PLATE

(Part# 02-07-0046)

Use this footer for 3-1/2” Upright

Use this footer for 1-1/4” Handrails and support posts.

(2) UPPER HOLES

Bolt uprights to footer using top(2) holes if Engineered Wood Fiber(mulch)
is used. Cover play surface to a depth of 12”

Bolt component to footer using top hole if Engineered Wood Fiber(mulch)
is used. Cover play surface to a depth of 12”

Bolt uprights to footer using bottom (2) holes if 2” rubber tiles or poured-in-place
surfacing is used.

Bolt component to footer using bottom hole if 2” rubber tiles or poured-in-place
surfacing is used.

(2) LOWER HOLES

UPPER HOLE

LOWER HOLE

This footer is only used for installations secured in-ground with concrete.
This plate is bolted in (3) places to upright and handrail footers.

See In-ground Footer Detail

This footer is used for 1-1/4” extension posts.
Attach extension posts of slides, ADA Step and
climbers to this plate.

FOOTERS

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands