UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 3

Page: 3 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

Dear UPlay Today™ Customer,

Thank you for choosing to purchase and install a UPlay Today™ commercial playsystem by

UltraPlay™. We appreciate the con

ﬁ

dence you have placed in our company and we will strive to

earn your trust.

This is your UPlay Today™ Owner’s Manual & Assembly Instructions booklet. We have designed

this manual speci

ﬁ

cally for the products that you have purchased. Included in this manual you

will

ﬁ

nd the following: a suggested maintenance schedule & record, safety guidelines, warranty

information, product installation instructions, a 2-D top view drawing and the ground plan.

Please save it for future reference.

The

ﬁ

rst several pages of this booklet contain important and valuable information regarding

the general placement, installation and safety practices common to commercial play equip-

ment. Please read this information carefully and use your best judgement as to how these

guidelines apply to your speci

ﬁ

c situation.

If you have any questions concerning your new equipment, you can contact a UPlay Today™

Customer Service Representative at 1-800-458-5872 or reach them electronically by sending

an e-mail to: [email protected].

For more information on UPlay Today™ and UltraPlay™ products, please do not hesitate to give

us a call or visit uplaytoday.com & ultraplay.com.

Thank you for your business; we look forward to working with you on all of your future play-

ground equipment projects!

Sincerely,

UPlay Today

™

PlaySystems by UltraPlay

™

A PlayCore

Company

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands