UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 29

Page: 29 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

STEP 1 - SECURE UPRIGHTS TO FOOTERS

1. Place (4)Uprights(A) on ground.

2. Unwrap and remove Footer(B)
from inside of Upright(A) to
observe hole placement.

3. Choose the appropriate set of
holes in Footer(B) depending on
your surfacing application and
align with holes in Upright(A).

NOTE: Top (2) holes used in illustration
selected for 12”
EWF (Engineered Wood Fiber)

4. Insert (2)Bolts(C) through aligned holes
and secure with Barrel Nuts(D) as shown.

NOTE: Head of Bolt(C) is inserted
through the large hole in
Upright(A) and will tighten
inside tube.

5. Repeat Steps 2 through 4
for the remaining (3)Posts(A).

NOTE: If installing playground with concrete
footers, install In-ground
footers at this time.

Parts List

Letter Description

Quantity Part Number

Uprights w/clamp

02-07-0001
02-07-0042
33-12-0026
33-11-0011
33-11-0401

Upright Footers

Hardware Complete

M10 x 80 BHCS Bolt

M10 Barrel Nut

Use top holes
for 12” EWF

Use bottom holes for
2” Poured-in-place
or rubber tiles

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands