UPlay Today ABT-DXBN-N Assembly Instructions Manual Download Page 30

Page: 30 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

4th post
removed
for clarity

1. Lift (4) 11ft Uprights into position
with clamp flange pointing inward.

2. Position Deck(A) onto clamp flange
of (4) 11ft Uprights.

3. Align hole in clamp flange with slot on
underside of Deck(A).

See Figure 1

4. Insert Bolt(B) and Flat Washer(C) upward
into hole in Clamp and through slot in Deck(A).
While pushing upright tightly against Deck(A),
secure with Flat Washer(C) and Lock Nut(D).

5. Repeat Steps 3 and 4 for remaining Uprights.
Tighten all hardware.

6. Level deck and make the
appropriate adjustments.

Clamp

Flange

Figure 1

Parts List

Letter Description

Quantity Part Number

02-07-0003
33-12-0019
33-11-0004
33-11-0200
33-11-0400

36-3/4” (933mm) Deck

Hardware Complete

M10 x 30 BHCS Bolt

M10 Flat Washer

M10 Lock Nut

Deck coating may prevent insertion of hardware.
Trim out slots with utility knife if necessary.

Posts must be supported until
all hardware is installed.

Uprights

STEP 2 - CONNECT DECK TO UPRIGHTS

Summary of Contents for ABT-DXBN-N


















































































Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands

UPlay Today ABT-DXBN-N, Assembly Instructions Manual

Search results

Summary of Contents for ABT-DXBN-N

Reviews:

Related manuals for ABT-DXBN-N

Brands by name

Popular brands