Unipulse M525B Operation Manual Download Page 64

Page: 64 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

Print Every and GT/ST Print formats are printed.
Test print is executed by pressing

(2)

→

(ENT) in the maintenance mode.

Sample of printing (partial)

* As a sample, 220 lines are printed in total (approximately 75cm).

The ROM and RAM of the M252B are tested, and the results are printed.
Press (3)

→

(ENT) in the maintenance mode, and the buzzer sounds and the test starts.

Results of check

2: Sample Print

************************
** SAMPLE PRINT No.3 **
************************

A---00 9876 12345kg
************************
** SAMPLE PRINT No.2 **
************************

05:09 9876 12345kg
************************
** SAMPLE PRINT No.1 **
************************

9876 12345kg
************************
** SAMPLE PRINT No.0 **
************************

(

↑

Print continues.)

3: Self Test

Results of test

Normal :

〇

Abnormal :

｛

* The description of SUM varies depending on the ROM version.

--------------------------
>> SUM:2AE
>> ROM:

〇

>> RAM:

〇

>> Checking...

--------------------------

If the result of Self Test is

or the test does not finish normally, the M252B may

be faulty.
Ask your deaer representative or for sevicing.

Attention

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands