Unipulse M525B Operation Manual Download Page 33

Page: 33 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Examples of print

8. Double print

                 389.3kg
   500.0kg
                   78.1kg
   1444.0kg
                 420.2kg
   150.5kg

Ach input data

Bch input data

   3 389.3kg
46    500.0kg
    2 78.1kg
45    1444.0kg
   1 420.2kg
44    150.5kg

Count

Bch input data

Count

Ach input data

9. Double print with count

12. Through print

Characters sent from the RS-232C interface in ASCII code are printed as they are. Start/stop
through print with the

(PRINT) key. If the

(PRINT) key is pressed during

through print,an offline state will result, so that through print cannot be performed.
If the

(PRINT) key is ressed again, an online state will result, so that through print can

be performed. FEED (paper feed) is valid only in an offline state.

HIGK

389.3g

STU

300.0kg

HIGK

789.3g

STU

450.0kg

HIGK

389.3g

STU

500.0kg

10. Double print with code

Code

Bch input data

11. Ach <-- A or B

Ach input data

389.3kg

300.0kg

789.3kg

450.0kg

389.3kg

500.0kg

Count

Bch input data

Ach input data

6. Diagram

Input data

500.5kg

450.2kg

1200.0kg

-385.8kg

55.0kg

Input data

Displacement diagram

｛

TARGET

50.0kg

RANGE 50.0kg

Example

Input data is printed horizontally
double size. However, the unit can be
printed only up to four characters.

7. Double size print (data)

-0.2L
48.7
78.5
102.1U

Lower

Target

Upper

▲

limit

Value

limit

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands