Unipulse M525B Operation Manual Download Page 38

Page: 38 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Examples of print

4. With histogram

------------------------
HI   1

U4   0
U3   2
U2   1
U1   3
T     0
L1   1
L2   1
L3   0
L4   0

LOW   1

HIGHEST   121 ～
U4       117 ～   120
U3       112 ～   116
U2       108 ～   111
U1       103 ～   107
T          98 ～   102
L1        93 ～    97
L2        89 ～    92

L3         84 ～   88
L4         80 ～   83
LOWEST       ～    79

H OVER TIMES         1
L OVER TIMES         1
RANGE              20kg
TARGET             100kg

R(MAX-MIN)        51kg
MIN                72kg
MAX                123kg
AVE                103kg
σn               14kg

GT                1031kg
COUNT              10
CODE           ABCDE
DATE   2000/06/21 13:01

--- GRAND TOTAL Ach ---

(Continued to the lower right)

(Continued from the upper left)

Direction of print

Times

Histogram

Range

target

range

Number of

Upper limit
violation over

Lower limit
violation over

Ach and Bch are the same in
unit, the grand total all of
both ch's is printed after
printingthe total of each ch.

Ach: Code Name WXYZA
Bch: Code Name ABCDE

------------------------
GT 2300kg
COUNT 20
--- GRAND TOTAL ALL ---

GT                1250kg
COUNT              10
CODE           ABCDE
DATE    2000/07/05 01:25

--- GRAND TOTAL Bch ---

GT                1050kg
COUNT              10
CODE           WXYZA
DATE    2000/07/05 01:25

--- GRAND TOTAL Ach ---

Ach

Bch

Grand total

grand total

both ch's

Point

If the decimal place setting
of each ch is different,
automatic totaling will result
according to the ch with a
larger number of decimal
places.

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands