Unipulse M525B Operation Manual Download Page 75 | Manualshive

Page: 75 / 85

background image

66

7

　

TROUBLESHOOTING

66

OPTION

Chapter

7

A ribbon cassette has not been installed, or the ribbon cassette is out of ink.

Referring to "2-1.Installing a Ribbon Cassette" on page 7, install or replace the
ribbon cassette.

SI/F signals from the load cell indicator include indicated and various kinds of weight
data irrespective of the value indicated by the indicator at that time.

elect data to be printed on the printer side. Set referring to "Print Data Selection Ach/
Bch" (page 19).

7-3.

The Printer Does not Function Properly

Counts are stored in battery-required memory. If the power is turned off and on again
with the battery exhausted, a problem occurs such that printing is not counted
normally.

The battery needs to be replaced. Since the battery should be replaced by
UNIPULSE, contact your dealer representative. The average life of the battery is
approx. 8 years. The time may also be incorrect if the battery is exhausted.

The decimal point position printed by the M252B depends on that of the indicator
side. If the decimal point position on the indicator side is changed during printing,
sub totals / grand totals are not calculated properly.

Never change the decimal point position of the indicator during printing. Change the
decimal point position after finding grand totals and clearing print data.

Data to which over status (R print) is added is not added.

Check that over status (R print) is not added to the print data.
The over status occurs due to indicator side trouble. Troubleshoot it referring to the
instruction manual of the indicator.

Although the printer head is running, nothing is printed.

Trouble 4

Cause 1

Remedy1

Values different from those indicated by the load cell indicator are printed.

Trouble 5

Cause 1

Remedy1

Printed counts are wrong.

Trouble 1

Cause 1

Remedy1

Values of sub totals / grand totals are wrong.

Trouble 2

Cause 1

Remedy1

Cause 2

Remedy1

«
...
73
74
75
76
77
...
»

Summary of Contents for M525B






















































































Reviews:

No comments

Related manuals for M525B

Brand: Xerox Pages: 73

Brand: Xerox Pages: 2

Brand: VASTEX Pages: 15

Brand: Xerox Pages: 2

Brand: Xerox Pages: 11

Brand: Xerox Pages: 192

Brand: Xerox Pages: 10

Brand: Xerox Pages: 15

WORKCENTRE 7425

Brand: Xerox Pages: 88

Brand: Xerox Pages: 10

Brand: Xerox Pages: 33

C123 Copycentre

Brand: Xerox Pages: 154

WorkCentre 5845

Brand: Xerox Pages: 14

WorkCentre 7132

Brand: Xerox Pages: 3

Brand: Datamax Pages: 95

Mark II E-4205e

Brand: Datamax Pages: 72

Brand: Canon Pages: 20

PIXMA TS9100 Series

Brand: Canon Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands