Unipulse M525B Operation Manual Download Page 37

Page: 37 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Select the print format of grand totals and sub totals.
Five types of formats can be selected.

Examples of print

Name of setting

11: GT/ST Print Format

Selection item

0. Standard (initial value)
1. With code
2. With ave/max/min
3. With statistical
4. With histogram

Reference

If Double print is selected under [Print Every Format] and Ach and Bch are the
same in unit, the grand total all of both ch's is printed after printingthe total of
each ch.

11: GT/ST Print Format

0. Standard

1. With code name

2. With avg./max/min

3. With statistical data

------------------------
GT                1250kg
COUNT              10
DATE   2000/07/05 01:25

--- GRAND TOTAL Ach ---

------------------------
GT                1250kg
COUNT               10
CODE           ABCDE
DATE   2000/07/05 01:25

--- GRAND TOTAL Ach ---

------------------------
R(MAX-MIN)      1903kg
MIN               554kg
MAX             2457kg
AVE             1352kg
σn              675kg

GT              13515kg
COUNT              10
CODE           ABCDE
DATE   2000/08/02 21:39

--- GRAND TOTAL Ach ---

------------------------
H OVER TIMES        2
L OVER TIMES        1
RANGE               20kg
TARGET             100kg

R(MAX-MIN)         122kg
MIN                 0kg
MAX                122kg
AVE                 94kg
σn                 32kg

GT                1036kg
COUNT              11
CODE           ABCDE
DATE   2000/06/21 13:01

--- GRAND TOTAL Ach ---

Direction of print

Maximum

Minimum
Maximum
Average
Standard

Number of

- minimum

deviation

Upper limit
violation over

Lower limit
violation over

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands