Unipulse M525B Operation Manual Download Page 22

Page: 22 / 85

CONNECTING WITH INDICATORS

CONNECTING WI

TH INDICATORS

Chapter

3-4.

About Input ch's

The M252B has two data input ch's. When using both ch's, select “8. Double print” or “9. Double
print with count” for [07: Print Every Format].

The following table shows input data to be printed.

①

Data input to SIF Ach is printed.

②

Data input to SIF Bch is printed.

OP:

Data input to an option (BCD input or RS-232C) is printed.

Single print:

When the [Print Every Format] setting is not “Double print”.

Double print:

When the [Print Every Format] setting is “Double print”.

Shaded part:

The alarm (buzzer) sounds.
See "3-5.Print Data Input ch's and Alarm Sound" on page 14 for details.

Input data

Single print

Double print

Ach

Bch

Ach

Bch

Without OP

SIF Ach

①

SIF Bch

②

SIF Ach + Bch

①

②

With OP

SIF Ach

①

SIF Bch

②

SIF Ach + Bch

①

②

SIF Ach + OP

①

SIF Bch + OP

②

SIF Ach + Bch + OP

①

②

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands