Unipulse M525B Operation Manual Download Page 42

Page: 42 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Select whether or not the print data is targeted for grand totals/sub totals.

Details of settings

The print data is targeted for grand totals/sub totals.

OFF

The print data is not targeted for grand totals/sub totals.
" * " (asterisk) is printed at the end of the printed data.

Meaning of setting

This setting is for testing printing after changing the setting(s) of equipment. Normally use at
ON.

Select whether the

(PRINT) key on the front panel is ON or OFF.

Meaning of setting

Select [OFF] if you do not want to print through a careless operation of the automatic
equipment, etc.

Name of setting

18: Data Adding ON/OFF

Selection item

. O

1. ON (initial value)

Caution

If Data Adding OFF is selected, printing is produced irrespective of the setting
of [06: Print Every ON/OFF].

Name of setting

19: PRINT Key ON/OFF

Selection item

0. OFF
1. ON (initial value)

Caution

This setting is irrelevant to the PRINT terminal on the rear panel and an
automatic print command from the SI/F or RS-232C interface.

18: Data Adding ON/OFF

GT              300.57kg
COUNT              3
DATE   2000/07/01 10:00
--- GRAND TOTAL Ach ---
3             100.15kg

2             100.56kg*
2             100.47kg*

2             100.21kg
1             100.21kg

Example of setting

Changed to ON

Changed to OFF

Actually, setting
operations (print) for
a change should be
performed.

(Omitted)

in this interim.

19: PRINT Key ON/OFF

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands