Unipulse M525B Operation Manual Download Page 72

Page: 72 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

6-5.

Initialization

The internal memory of the M252B is completely cleared, and the parameters are restored to their
factory default settings.

Turn on the power while pressing the

(A) key.

Since the following is printed, press

(ENT).

If the following is printed, initialization is successful.

6-6.

ROM Version Print

Press (6)

→

(ENT) in the print mode, and the ROM version is printed.

When the version is printed, the option name(s) is printed if any.

6-7.

Date Print

Press (DATE)

→

(ENT) in the print mode, and the current time is printed.

Cancel --> ESC
OK --> ENT
----All data initial----

operating

To execute initialization:

To cancel initialization:

[ENT]

[ESC]

------------------------
>> Complete

Deleted data or settings cannot be restored. Carefully perform this operation.

Attention

------------------------
Ver.1.03
------------------------

Ver.5.00

Op 232

Ver.5.00

Op BCD

DATE 2000/07/04 23:19

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands