Unipulse M525B Operation Manual Download Page 5 | Manualshive

Page: 5 / 85

background image

CAUTION

IV

CAUTION

IV

CAUTION

　

●

For turning on/off the power, be sure to keep intervals of 5 seconds or more.

●

After power-on, make sure to warm up the M252B for at least 30 minutes or more before use.

●

If the M252B is not used by the specified method, its protective performance may be
impaired.

●

Maintenance
- When performing maintenance, disconnect the power.
- Do not wipe with a wet rag, or with benzine, thinner, alcohol, etc. Doing so may cause

discoloration or deformation of the M252B. In the case of heavy contamination, wipe off
the contamination with a cloth after dipping it into a diluted neutral detergent and wringing
it well, and then wipe with a soft, dry cloth.

●

Do not open the front cover with the power on when replacing the ribbon cassette, etc. The
printer may start sudden movement, and you may injure yourself.

●

Do not drop foreign objects such as screws inside the printer. If an object is dropped,
immediately turn off the power, and completely remove the foreign object before using the
printer.

●

Do not touch the print head immediately after printing because the print head is hot.

●

Never print without paper or a ribbon cassette. Also, do not print out of the paper width.

●

Be sure to use a specified ribbon cassette. Use of an unspecified one will cause a failure.

●

If the print is light or the ink ribbon is ragged, replace the ribbon cassette. If the ribbon
cassette is left for a long time in an unpacked condition, its life will shorter.

●

After replacing the ribbon cassette, check that the ink ribbon is not slack. If slack, turn the
knob in the direction of the arrow to remove the slack before operation.

●

Use paper appropriate to the specifications.

●

When the M252B is shipped, spacers made of corrugated cardboard are used as cushioning
materials.
Though it is factory-designed so that shocks can sufficiently be absorbed, breakage may
result if shocks are applied when the spacers are reused for transportation. If you send the
M252B to us for repair, etc., take adequate measures against shocks by using polyurethane
materials, etc., separately.

●

If you dispose of the product, handle it as industrial waste.

This sign forewarns the presence of hazards

that could result in personnel injury or property
damage when incorrectly handled.

Caution during startup and maintenance

Caution during use

Caution during transportation

Caution during disposal

«
...
3
4
5
6
7
...
»

Summary of Contents for M525B






















































































Reviews:

No comments

Related manuals for M525B

Brand: Olympus Pages: 71

Brand: Eazao Pages: 50

Brand: Nantian Electronics Pages: 4

Brand: Labelmate Pages: 2

AdvancedPunch Pro

Brand: GBC Pages: 92

Brand: Ricoh Pages: 406

Brand: A&D Pages: 8

Brand: Oki Pages: 107

Accel a Writer 812

Brand: Xante Pages: 312

Brand: idp Pages: 48

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: Konica Minolta Pages: 424

D-color MF 250 Plus

Brand: Olivetti Pages: 276

Brand: Ultimaker Pages: 4

Brand: Oki Pages: 72

Brand: QMS Pages: 188

Brand: Sinfonia Technology Pages: 41

Brand: Oki Pages: 239

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands