Unipulse M525B Operation Manual Download Page 61

Page: 61 / 85

ADVANCED USE

ADVANCE

D USE

Chapter

6-2.

Maintenance Mode

In the maintenance mode, operations of the M252B are checked.

■

Method for Operating the Maintenance Mode

How to enter each item in the maintenance mode and procedures for each execution are described
below. Here, test print is performed as an example.

Press (F)

→

(ENT), and the following is printed.

To enter the maintenance mode, press

(3)

→

(ENT) successively.

Test Print

All characters that can be printed by the M252B are printed.
The data input status is printed.

Sample Print

Print Every and GT/ST Print formats are printed.

Self Test

The ROM and RAM of the M252B are tested, and the results are
printed.

Parameter List

A list of current parameters of the M252B is printed.

Test Mode

For factory check (Do not use).

* For details of the setting and option setting modes,

--------------------------
Cancel/End

-->

ESC

Maintenance

-->

3-ENT

Option Setting -->

2-ENT

Setting

-->

1-ENT

==========================

Select

==========================

To enter the setting mode:

To enter the option setting mode:

To cancel or end:

To enter the maintenance mode:

operating

[1]

→

[ENT]

[2]

→

[ENT]

[3]

→

[ENT]

[ESC]

see the respective explanations.

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands