UNI-T UPO2000CS Series User Manual Download Page 8 | Manualshive

Page: 8 / 94

background image

UPO2000CS series User Manua

7

Introduction of UPO2000CS series digital phosphor oscilloscope

UPO2000CS series digital oscilloscopes contains the following 5 models

Model

Analog Channels

Bandwidth

UPO2104CS

4

100MHz

UPO2074CS

4

70MHz

UPO2102CS

2

100MHz

UPO2072CS

2

70MHz

UPO2202CS

2

200MHz

UPO2000CS series digital oscilloscope is based on UNI-T’s unique Ultra Phosphor technology. A
multi-functional, high performance oscilloscope that is easy to use, with excellent technical specifications, a
perfect combination of many functionalities that can help users to quickly complete testings. UPO2000CS
series is aimed at satisfying the most extensive oscilloscope markets, including communications,
semiconductors, computers, aerospace defense, instrumentation, industrial electronics, consumer electronics,
automotive electronics, field maintenance, R&D, education, etc.

The main features of the UPO2000CS series are:

●  200MHz/100MHz/70MHz bandwidth, providing 2-channel and 4-channel models
●  Real-time sampling rate of up to 1GS/s, can also observe faster signals
●  Standard storage depth of 28Mpts per channel, which allows the oscilloscopes to maintain a high

sampling rate in a wider time base, taking into account the structure and details of the waveform

● Waveform capture rate of up to 50,000wfms/s
● Real-time continuous hardware waveform recording and waveform analysis support waveform recording

up to 65,000 waveforms.

●  Multilevel gray scale display
●  8-inch WVGA (800 * 480) TFT LCD, ultra widescreen, vivid color, clear display
●  Abundant trigger features, including a variety of advanced trigger options
●  Standard configuration interface: USB-Host, USB-Device, LAN, and Pass/Fail
●  Automatic measurement of 34 waveform parameters
●  Supports USB storage and firmware upgrades, one click screen copy function
●  Plug and play USB device, can be used to communicate with computer

«
...
6
7
8
9
10
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: Dairyland Pages: 21

Brand: Keithley Pages: 42

Brand: SCHUNK Pages: 2

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brand: Bayer HealthCare Pages: 104

EDC2-1001-RGB-MWT

Brand: Energizer Pages: 18

Brand: MIETHKE Pages: 125

Brand: Stamina Pages: 22

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Monolith NT.115

Brand: Nano Temper Pages: 24

SCAFFOLDBENCH I-CISRL

Brand: MetalTech Pages: 16

Brand: Baileigh Industrial Pages: 40

Kids Cubby House

Brand: Mocka Pages: 5

Tidland Performance Series

Brand: Maxcess Pages: 72

Brand: Agilent Technologies Pages: 6

ARCH RIVAL CR4250-S

Brand: Big Game Treestands Pages: 30

Brand: STRIKEMASTER Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands