UNI-T UPO2000CS Series User Manual Download Page 17

Page: 17 / 94

UPO2000CS series User Manual

(4)Auto Setting

When this key is pressed, the oscilloscope will automatically adjust the vertical scale factor,
timebase, and trigger mode according to the input signals.

(5)Run/Stop

Press the key to "run" or "stop" sampling. RUN state is indicated by green light. STOP state is
indicated by red light.

(6)Single

Set to single trigger mode.

(7)Clear

Clear all waveforms on the screen. If the oscilloscope is in the "RUN" state, it will continue to
display new waveforms.

(8)Screen Copy

Copy the screen to a BMP format image and store it to USB device.

(9)Multipurpose Knob

•

During non-menu operations: Turn the knob to adjust display brightness. You can also

press the DISPLAY button and choose the waveform brightness option, then use the
knob to adjust the brightness.

•

During menu operations: Turn the knob to select submenu, then press the knob to

confirm selection.

(10)Function Keys

MEASURE: Measure setting menu: can set measure source

to all parameters, custom parameters, perform measurement
statistics, select measurement indicators, etc.

ACQUIRE: Sampling setting menu to set up acquisition mode

Summary of Contents for UPO2000CS Series































































































Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands

UNI-T UPO2000CS Series, User Manual

Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands