UNI-T UPO2000CS Series User Manual Download Page 10

Page: 10 / 94

UPO2000CS series User Manua

Chapter 3 Trigger System ................................................................................................................................................. 22

3.1Trigger System Interpretation ................................................................................................................................ 22

3.16

SPI Protocol Trigger and Decode( Optional) ...................................................................................................... 45

Chapter 4 Set Level System .............................................................................................................................................. 50

Chapter 5 Mathematical Operations................................................................................................................................ 53

Chapter 6 Set Sampling System ....................................................................................................................................... 57

6.1 Sampling Rate........................................................................................................................................................ 57

(1) Sampling and Sampling Rate ......................................................................................................................... 57
(2) Low Sampling Rate Effect ............................................................................................................................... 58

6.2 Acquisition Mode .................................................................................................................................................. 58

(1) Normal Sampling ........................................................................................................................................... 58
(2) Peak Sampling ................................................................................................................................................ 58

Summary of Contents for UPO2000CS Series































































































Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands

UNI-T UPO2000CS Series, User Manual

Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands