UNI-T UPO2000CS Series User Manual Download Page 31

Page: 31 / 94

UPO2000CS series User Manual

Slope

Rising Edge

Triggers when the input signal level at the rising edge is above
the set level

Falling Edge

Triggers when the input signal is at falling edge and voltage level
is higher than high trigger level.

Any Edge

Triggers when the input signal is at any edge and the voltage
level meet trigger setting.

Trigger
Setting

Enters trigger setting menu

Enters Beyond-range Trigger Menu (2)

Beyond-range Trigger Menu (2)

Functions Options

Descriptions

Position

Enter

Triggers when input signal enters trigger level range

Return

Triggers when input signal leaves trigger level range

Time

Triggers when time in trigger level mode matches set time

Trigger
Level

High

The beyond-range high threshold level can be adjusted with the

LEVEL knob

Low

The beyond-range low threshold level can be adjusted with the

LEVEL knob

Setting

8.0ns~10ns

Using the multipurpose knob to set the pulse width time to be
between 8.0ns~10.0s

Return

Return to beyond-range trigger main menu

3.8 Delayed Trigger

To select delayed trigger mode, trigger source 1 and 2 need to be set. Trigger event occurs when the time between
the two trigger sources is met.
Note: Source edges 1 and 2 must be neighboring edges.

Summary of Contents for UPO2000CS Series































































































Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands

UNI-T UPO2000CS Series, User Manual

Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands