UNI-T UPO2000CS Series User Manual Download Page 12 | Manualshive

Page: 12 / 94

background image

UPO2000CS series User Manua

11

Chapter 1 Introduction Guide

This chapter introduces on using the oscilloscope for the first time, the front and rear panels, the user interface,
as well as the built-in help system.

1.1 General Inspection

It is recommended to follow the steps below before using the UPO2000CS series for the first time.

(1) Check for Damages caused by Transport

If the packaging carton or the foam plastic cushions are severely damaged, please contact the UNI-T
distributor of this product immediately.

(2) Check Attachment

Please check Appendix A for the list of accessories. If any of the accessories are missing or damaged, please
contact UNI-T or local distributors of this product.

(3) Machine Inspection

If the instrument appears to be damaged, not working properly, or has failed the functionality test, please
contact UNI-T or local distributors of this product.
If the equipment is damaged due to shipping, please keep the packaging and notify both the transportation
department and UNI-T distributors, UNI-T will arrange maintenance or replacement.

1.2 Before Use

To perform a quick verification of the instrument’s normal operations, please follow the steps below:

(1) Connect to the Power Supply

The power supply voltage range is from 100 VAC to 240 VAC, the frequency range is 45Hz to 440Hz. Connect
the oscilloscope to the power supply line that came with the oscilloscope or any power supply line that meets
the host country standards. Turn the power button on the back of the oscilloscope to ON. Now the soft power
button

in the front of the oscilloscope should be lit green.

(2) Boot Check

Press the soft power button

and the light should change to yellow. The oscilloscope then will show a boot

animation, and it will enter the normal interface afterwards.

«
...
10
11
12
13
14
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: Navman Pages: 17

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: Samson Pages: 2

Brand: TC Electronic Pages: 4

Brand: TC Electronic Pages: 6

Brand: TC-Helicon Pages: 12

Brand: TC Electronic Pages: 76

Brand: Ultraflex Pages: 48

Brand: Zell Pages: 32

Brand: Uflex Pages: 16

Air 2000 Outdoor

Brand: ubbink Pages: 21

Brand: M-system Pages: 4

Brand: Flex-A-Seal Pages: 7

Brand: Topcon Pages: 38

Brand: Exmark Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands