UNI-T UPO2000CS Series User Manual Download Page 3 | Manualshive

Page: 3 / 94

background image

UPO2000CS series User Manual

2

Copyright and Satement

Copyright Information

•

UNl-T Uni-Trend Technology (China) Limited. All rights reserved.

Trademark Information

•

UNI-T is the registered trademark of Uni-Trend Technology (China) Limited.

Document Version

UPO2000CS-20160414-EN-V1.3

Statement

·

UNI-T

products are protected by patent rights in China and foreign countries, including issued and pending

patents.

·

UNI-T

reserves the rights to any product specification and pricing changes.

·

UNI-T

reserves all rights. Licensed software products are properties of Uni-Trend and its subsidiaries or

suppliers, which are protected by national copyright laws and international treaty provisions.

·

Information in this manual supercedes all previously published versions.

Warranty

UNI-T warrants that the product will be free from defects for a three-year period. If the product is re-sold, the
warranty period will be from the date of the original purchase from an authorized UNI-T distributor. Probes,
other accessories, and fuses are not included in this warranty.

If the product is proved to be defective within the warrenty period, UNI-T reserves the rights to either repair the
defective product without charging of parts and labor, or exchange the defected product to a working
equivalent product. Replacement parts and products may be brand new, or perform at the same specifications
as brand new products. All replacement parts, modules, and products become the property of UNI-T.

The “customer” refers to the individual or entity that is declared in the guarantee. In order to obtain the
warranty service, "customer" must inform the defects within the applicable warranty period to UNI-T, and to
perform appropriate arrangements for the warranty service. The customer shall be responsible for packing and
shipping the defective products to the designated maintenance center of UNI-T, pay the shipping cost, and
provide a copy of the purchase receipt of the original purchaser. If the product is shipped domestically to the
location of the UNI-T service center, UNI-T shall pay the return shipping fee. If the product is sent to any other

«
1
2
3
4
5
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: Parr Instrument Pages: 24

Brand: JBL Pages: 15

Brand: Gardena Pages: 19

Brand: Jackco Pages: 6

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: Nemalux Pages: 6

Brand: OBDLink Pages: 2

Brand: LAPPSET Pages: 16

Brand: Pari Pages: 11

Brand: Pari Pages: 2

Brand: Haas Pages: 5

Brand: Tar River Pages: 44

Brand: Tar River Pages: 61

Brand: Quadro mdb Pages: 9

Brand: NAMYSLO Pages: 13

Brand: A.J.Antunes Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands