UNI-T UPO2000CS Series User Manual Download Page 4 | Manualshive

Page: 4 / 94

background image

UPO2000CS series User Manua

3

location, the customer shall be responsible for all shipping, duties, taxes, and any other expenses.

This warranty shall not apply to any defects or damages caused by acciendental, machine parts’ wear and tear,
improper use, and improper or lack of maintenance. UNI-T under the provisions of this warranty has no
obligation to provide the following services:
a) Any repair damage caused by the installation, repair, or maintenance of the product by non UNI-T service
representatives.
b) Any repair damage caused by improper use or connection to an incompatible device.
c) Any damage or malfunction caused by the use of a power source which does not conform to the
requirements of this manual.
d) Any maintenance on altered or integrated products (if such alteration or integration leads to an increase in
time or difficulty of product maintenance).

This warranty written by UNI-T for this product, and it is used to substitute any other express or implied
warranties. UNI-T and its distributors do not offer any implied warranties for merchatability or applicability
purposes.
For violation of this guarantee, UNI-T is responsible for the repair or replacement of defective products is the
only remedy available to customers. Regardless of whether UNI-T and its distributors are informed that any
indirect, special, incidental, or consequential damage may occur, the UNI-T and its distributors shall not be
responsible for any of the damages.

«
...
2
3
4
5
6
...
»

Summary of Contents for UPO2000CS Series































































































Reviews:

No comments

Related manuals for UPO2000CS Series

Brand: MAHLE Pages: 21

Brand: YATEK Pages: 72

Brand: Quincy lab Pages: 4

Brand: B&G Pages: 3

Brand: Parker Pages: 39

Brand: RAPID REBOOT Pages: 18

Brand: MacDon Pages: 170

Brand: MacDon Pages: 108

Brand: MacDon Pages: 108

Brand: MacDon Pages: 51

Brand: MacDon Pages: 104

Brand: MacDon Pages: 240

QUANTOFIX Relax

Brand: Macherey-Nagel Pages: 192

Brand: MacDon Pages: 182

Brand: MacDon Pages: 192

Brand: MacDon Pages: 53

Brand: MacDon Pages: 2

Brand: Vatech Pages: 137

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands