UNI-T UPO2000CS Series User Manual Download Page 33

Page: 33 / 94

UPO2000CS series User Manual

between 8.0ns~10.0s

Enters Delayed Trigger Menu (3)

Delayed Trigger Menu (3)

Functions Options

Descriptions

Trigger
setting

Enters trigger setting menu

Return

Return to delayed trigger main menu

3.9 Overtime Trigger

Overtime trigger occurs when the input signal’s pulse width

△

t (time between rising and falling edge) is greater than

the overtime set time.

Press the TRIG MENU button to enter the trigger menu. Press F1 to select trigger type, use the multipurpose knob
to select to overtime trigger mode.

Overtime Trigger Menu:

Functions Options

Descriptions

Type

Overtime

Source 1

CH1, CH2, CH3,
CH4

Set any one of the CH1~CH4 as a trigger signal

Slope

Rising

Time starts at the rising edge of signal

Falling

Time starts at the falling edge of signal

Any

Time starts at any edge of signal

Overtime
Time

8ns~10s

Set overtime trigger time

Trigger
Setting

Enters trigger setting menu

Summary of Contents for UPO2000CS Series































































































Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands

UNI-T UPO2000CS Series, User Manual

Search results

Summary of Contents for UPO2000CS Series

Reviews:

Related manuals for UPO2000CS Series

Brands by name

Popular brands