background image

 

 

http://u-prox.com 

26 

Connection 

Wired  or  wireless  computer  network  used  for  U-Prox  IP100    communication  to  the 
ACS server. Device setup is possible with using autoconfiguration or manually with a 
PC using the software "Configurator": 

Appropriate configuration provides: 

 

Assigning of static or dynamic (DHCP) IP address to a device; 

 

Working with two (primary and backup) IP or DNS (Domain Name Service) 
of ACS server addresses; 

 

Working  on  the  Internet  (service  of  remote  branches)  with  the  ability  of  
reserving paths to the Internet via the second router; 

 

Use two Wi-Fi access points (primary and backup) 

Panel  works  automatically  after  data  upload  from  the  ACS  server.  It  processes 
access rights for IDs passed grants or denies access and sent event reports to the 
server. 

Panel communicator operates in notification mode. If there is event (passage,  input 
violation) data transmission to ACS server is initiated. 

Panel provides protection against arbitrary interference due to the encryption of data 
with 256-bit key and against panel substitution supervising the unique serial number 
of  the  device  at  its  work  in  the  network.  It  also  provides  supervision  of  the 
communication channel by means of periodic test signals from the device. 

 

Wired computer network (Ethernet) 

Ethernet interface is used to connect components of the system (PC and panels) in 
the  network.  Ethernet  cable  length  without  additional  equipment  can  be  up  to  100 
meters.  

Use  standard  Ethernet  cable,  which  involves  four  wires:  TX  ,  TX-,  RX  ,  RX-  for 
connection. Transfer rate is up to 100Mb / s. 

Ehernet 

clamps of 

panel's 

connector 

Cable color 

Clamps of 

RJ-45 

connector 

  

 

Direct connection  

(to the switch or router)

 

White-Yellow 

Yellow 

White-Green 

Green 

Summary of Contents for IP100































Reviews: