background image

 

 

http://u-prox.com 

About this document 

T

his  manual  covers  installation,  adjustment  and  utilization  of  U-Prox  IP100  

(hereinafter panel) access control panel. Read this manual carefully prior to installing 
the system. 

Characteristics,  Intended  use  and  parameters  of  the  panel  are  described  in  the 
section "

Summary

". Section "

Terms

" provides an explanation of terms found in this 

document. 

The  look  of  the  panel,  the  pins  and  the  mode  of  work  are  described  in  the 
"

Description  section

".  Order  of  installation,  adjustment  of  external  devices  and 

panel configuration are described in "

Working with the device

" section. 

 

Technical support 

To get warranty  and  technical support you can apply to authorized service centers, 
situated on the territory of countries, enlisted in the warranty card. 

Warranty and technical support are performed on the territory of the country, where 
the customer applied for warranty or free service. 

Technical information is available on the system website 

www.u-prox.com 

 

 

 

Attention! Read this manual carefully prior to installing the system. 

Installation,  adjustment  and  utilization  of  panel  is  allowed  only  to  persons  or 
organizations with the appropriate authority from the manufacturer 

Summary of Contents for IP100































Reviews: