TP-Link JetStream TL-SG3424P User Manual Download Page 253

Page: 253 / 263

Figure D-3 Welcome to the InstallShield Wizard

4) To continue, choose the destination location for the installation files and click

Next

on the

following screen.

Figure D-4 Choose Destination Location

By default, the installation files are saved on the Program Files folder of system disk. Click the

Change

button to modify the destination location proper to your need.

5) Till now, The Wizard is ready to begin the installation. Click

Install

to start the installation on

the following screen.

244

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands