TP-Link JetStream TL-SG3424P User Manual Download Page 225

Page: 225 / 263

Cluster Name:

Displays the cluster name of this device.

Role:

Displays the role this device plays in the cluster.

Commander: Indicates the device that can configure and
manage all the devices in a cluster.

Member: Indicates the device that is managed in a cluster.

Candidate: Indicates the device that does not belong to any
cluster though it can be added to a cluster.

Individual: Indicates the device with cluster feature
disabled.

Hops:

Displays the hop count from this device to the switch.

Neighbor Info:

Click the

Detail

button to view the complete information of this

device and its neighbors.

Collect Topology:

Click the

Collect Topology

button to collect NTDP information

of the switch so as to collect the latest network topology.

Click the

Detail

button to view the complete information of this device and its neighbors.

Figure 15-6 Information of the Current Device

15.2.2 NTDP Summary

On this page you can view the NTDP configuration.

Choose the menu

Cluster

→

NTDP

→

NTDP Summary

to load the following page.

216

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands