TP-Link JetStream TL-SG3424P User Manual Download Page 222

Page: 222 / 263

Figure 15-3 NDP Summary

The following entries are displayed on this screen:

Global Config

NDP:

Displays the global NDP status (enabled or disabled) for the
switch.

Aging Time:

Displays the period for the neighbor switch to keep the NDP
packets from this switch.

Hello Time:

Displays the interval to send NDP packets.

Port Status

Port:

Displays the port number of the switch.

NDP:

Displays the NDP status (enabled or disabled) for the current
port.

Send NDP Packets:

Displays the count of currently sent NDP packets.

Receive NDP Packets:

Displays the count of currently received NDP packets.

Error NDP Packets:

Displays the count of currently received error NDP packets.

Neighbors:

Displays the count of the connected neighbors.

213

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands