TP-Link JetStream TL-SG3424P User Manual Download Page 212

Page: 212 / 263

14.3 Device Statistics

You can view the LLDP statistics of the local device through this feature.

Choose the menu

LLDP

→

Device Statistics

→

Statistic Info

to load the following page.

Figure 14-5 LLDP Statistic Information

The following entries are displayed on this screen:

Auto Refresh

Auto Refresh:

Enable/Disable the auto refresh function.

Refresh Rate:

Specify the auto refresh rate.

Global Statistics

Last Update:

Displays latest update time of the statistics.

Total Inserts:

Displays the number of neighbors inserted till last update time.

Total Deletes:

Displays the number of neighbors deleted by local device.

Total Drops:

Displays the number of neighbors dropped by local device.

203

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands