TP-Link JetStream TL-SG3424P User Manual Download Page 139

Page: 139 / 263

Mask:

Displays the OUI address mask of the voice device.

Description:

Displays the description of the OUI.

Configuration Procedure of Voice VLAN:

Step Operation

Description

1 Configure

the

link type of the
port

Required. On

VLAN

→

802.1Q VLAN

→

Port Config

page, configure the

link type of ports of the voice device.

2 Create

VLAN Required.

VLAN

→

802.1Q VLAN

→

Port Config

page, click the

Create

button to create a VLAN.

3 Add

OUI

address

Optional. On

QoS

→

Voice VLAN

→

OUI Config

page, you can check

whether the switch is supporting the OUI template or not. If not, please
add the OUI address.

4 Configure

the

parameters of
the ports in voice
VLAN.

Required. On

QoS

→

Voice VLAN

→

Port Config

page, configure the

parameters of the ports in voice VLAN.

5 Enable

Voice

VLAN

Required. On

QoS

→

Voice VLAN

→

Global Config

page, configure the

global parameters of voice VLAN.

Return to CONTENTS

130

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands