TP-Link JetStream TL-SG3424P User Manual Download Page 149

Page: 149 / 263

Standard-IP ACL

and

Extend-IP ACL

pages.

11.2.1 ACL Summary

On this page, you can view the current ACLs configured in the switch.

Choose the menu

ACL

→

ACL Config

→

ACL Summary

to load the following page.

Figure 11-4 ACL Summary

The following entries are displayed on this screen:

Search Option

Select ACL:

Select the ACL you have created

ACL Type:

Displays the type of the ACL you select.

Rule Order:

Displays the rule order of the ACL you select.

Rule Table

Here you can view the information about the ACL rule you select.

11.2.2 ACL Create

On this page you can create ACLs.

Choose the menu

ACL

→

ACL Config

→

ACL Create

to load the following page.

Figure 11-5 ACL Create

The following entries are displayed on this screen:

Create ACL

ACL ID:

Enter ACL ID of the ACL you want to create.

Rule Order:

User Config order is set to be match order in this ACL.

140

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands