TP-Link JetStream TL-SG3424P User Manual Download Page 226

Page: 226 / 263

Figure 15-7 NTDP Summary

The following entries are displayed on this screen:

Global Config

NTDP:

Displays the NTDP status (enabled or disabled) of the switch
globally.

NTDP Interval Time:

Displays the interval to collect topology information.

NTDP Hops:

Displays the hop count the switch topology collects.

NTDP Hop Delay:

Displays the time between the switch receiving NTDP request
packets and the switch forwarding NTDP request packets for the
first time.

NTDP Port Delay:

Displays the time between the port forwarding NTDP request
packets and its adjacent port forwarding NTDP request packets
over.

Port Status

Port:

Displays the port number of the switch.

NTDP:

Displays NTDP status (enabled or disabled) of the current port.

217

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands