TP-Link JetStream TL-SG3424P User Manual Download Page 217

Page: 217 / 263

Figure 14-8 LLDP-MED Local Information

The following entries are displayed on this screen:

Auto Refresh

Auto Refresh:

Enable/Disable the auto refresh function.

Refresh Rate:

Specify the auto refresh rate.

Local Info

Enter the desired port number and click

Select

to display the information of the corresponding

port.

14.4.4 Neighbor Info

On this page you can get the LLDP-MED information of the neighbors.

Choose the menu

LLDP

→

LLDP-MED

→

Neighbor Info

to load the following page.

208

Summary of Contents for JetStream TL-SG3424P








































































































































































































































































Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands

TP-Link JetStream TL-SG3424P, User Manual

Search results

Summary of Contents for JetStream TL-SG3424P

Reviews:

Related manuals for JetStream TL-SG3424P

Brands by name

Popular brands